This section is specific to the Beaglebone Black hardware. If you're not using that hardware then just skip to the next section.

To get started you will need:

• A Beaglebone Black
• A MicroSD card
• Ethernet cable
• Optionally a 5V 2A power supply for the Beaglebone Black
• Access to the internet via a router with ethernet sockets
• USB thumb drive (for backups or storing media)
• One or more domains available via a dynamic DNS provider, such as https://freedns.afraid.org/
• A purchased domain name and SSL certificate (only needed for Red Matrix)
• A laptop or desktop machine with the ability to write to a microSD card (might need an adaptor)

You will also need to know, or find out, the IP address of your internet router and have a suitable static IP address for the Beaglebone on your local network. The router should allow you to forward ports to the Beaglebone (often this is under firewall or "advanced" settings).

You can either install from a debian package or manually as follows:

sudo apt-get update
sudo apt-get install git dialog build-essential
git clone https://github.com/bashrc/freedombone
cd freedombone
sudo make install

Plug the microSD card into your laptop/desktop and then run the freedombone-prep command. For example:

freedombone-prep -d /dev/sdX --ip freedombone_IP_address --iprouter router_IP_address

where /dev/sdX is the device name for the microSD card. Often it's /dev/sdb or /dev/sdc, depending upon how many drives there are on your system. The script will download the Debian installer and update the microSD card. It can take a while, so be patient.

When the initial setup is done follow the instructions on screen to run the main freedombone command.

Before running the freedombone command you will need a few things.

• Have some domains, or subdomains, registered with a dynamic DNS service
• System with a new installation of Debian Jessie
• Ethernet connection to an internet router
• It is possible to forward ports from the internet router to the system
• If you want to set up a social network or microblog then you will need SSL certificates corresponding to those domains
• Have ssh access to the system

If you have existing GPG keys then copy the .gnupg directory onto the system.

scp -r ~/.gnupg username@freedombone_IP_address:/home/username

The interactive server configuration setup is recommended for most users. On the system where freedombone is to be installed create a configuration file.

ssh myusername@freedombone_IP_address
su
sudo apt-get update
apt-get install git dialog build-essential
git clone https://github.com/bashrc/freedombone
cd freedombone
make install

Now the easiest way to install the system is via the interactive setup.

freedombone menuconfig

You can select which variant you wish to install and then enter the details as requested. A video of the install sequence can be seen here.

If you don't want to install interactively then it's possible to manually create a configuration file as follows:

On the system where freedombone is to be installed create a configuration file.

ssh myusername@freedombone_IP_address
su
sudo apt-get update
apt-get install git build-essential
git clone https://github.com/bashrc/freedombone
cd freedombone
make install
nano /home/myusername/freedombone/freedombone.cfg

Add the following, and set the values as needed. Note that for a full install DOMAIN_NAME should be the same as the wiki domain name.

MY_USERNAME=myusername
DOMAIN_NAME=mywikidomain
SYSTEM_TYPE=full
INSTALLING_ON_BBB=no
DDNS_PROVIDER=default@freedns.afraid.org
DDNS_USERNAME=ddnsusername
DDNS_PASSWORD=ddnspassword3471326
MY_NAME=MyFullNameOrNick
MY_EMAIL_ADDRESS=myusername@mywikidomain
LOCAL_NETWORK_STATIC_IP_ADDRESS=192.168.1.60
ROUTER_IP_ADDRESS=192.168.1.254
ENABLE_CJDNS=no
DEBIAN_REPO=ftp.us.debian.org
NAMESERVER1=85.214.73.63
NAMESERVER2=213.73.91.35
WIKI_TITLE=my wiki title
WIKI_DOMAIN_NAME=mywikidomain
MY_BLOG_TITLE=my blog
FULLBLOG_DOMAIN_NAME=myblogdomain
MICROBLOG_DOMAIN_NAME=mymicroblogdomain
REDMATRIX_DOMAIN_NAME=myredmatrixdomain
OWNCLOUD_DOMAIN_NAME=myownclouddomain

Both of the IP addresses are local IP addresses, typically of the form 192.168.x.x, with one being for the system and the other being for the internet router.

Save the configuration file and exit from your editor.

Now you can begin the installation. If you are doing this on a Beaglebone Black:

freedombone -c freedombone.cfg

The above command should be run in the same directory in which your configuration file exists.

Also see the manpage for additional options which can be used instead of a configuration file.

Setup of the server and installation of all the relevant packages is not quick, and depends upon which variant you choose and your internet bandwidth. Allow about three hours for a full installation on the Beaglebone Black. On the Beaglebone installation is in two parts, since a reboot is needed to enable the hardware random number generator and zram.

When done you can ssh into the Freedombone with:

ssh myusername@domain -p 2222

Any manual post-installation setup instructions or passwords can be found in /home/username/README. You should remove any passwords from that file and store them within a password manager such as KeepassX.

On your internet router, typically under firewall settings, open the following ports and forward them to your server.

You can configure laptops or desktop machines which connect to the Freedombone server in the following way. This alters encryption settings to improve overall security.

sudo apt-get update
sudo apt-get install git dialog haveged build-essential
git clone https://github.com/bashrc/freedombone
cd freedombone
sudo make install
freedombone-client