All integer code assume CPU of debuggee encode integers:
- little endian
- 2 complement for signed integers.
Signed-off-by: Eric Pouech <eric.pouech@gmail.com>
Signed-off-by: Alexandre Julliard <julliard@winehq.org>
As a side effect, the internal 'long int' type is now always 8 byte wide.
Signed-off-by: Eric Pouech <eric.pouech@gmail.com>
Signed-off-by: Alexandre Julliard <julliard@winehq.org>
Fixed listing twice the same symbol in some commands like 'break foo!bar'.
Signed-off-by: Eric Pouech <eric.pouech@gmail.com>
Signed-off-by: Alexandre Julliard <julliard@winehq.org>
Today, when gdbproxy is started with --no-start mode, GDB fails to
recognise the symbol file unless the `file` command or the
`sharedlibrary` command is explicitly issued.
Also, RHEL's downstream GDB complains with the following message:
Remote gdbserver does not support determining executable automatically.
RHEL <=6.8 and <=7.2 versions of gdbserver do not support such automatic executable detection.
The following versions of gdbserver support it:
- Upstream version of gdbserver (unsupported) 7.10 or later
- Red Hat Developer Toolset (DTS) version of gdbserver from DTS 4.0 or later (only on x86_64)
- RHEL-7.3 versions of gdbserver (on any architecture)
Fix this by implementing the qXfer object "exec-file".
Signed-off-by: Jinoh Kang <jinoh.kang.kr@gmail.com>
Signed-off-by: Rémi Bernon <rbernon@codeweavers.com>
Signed-off-by: Alexandre Julliard <julliard@winehq.org>
GDB does not retrieve the result of a qXfer command at once; instead, it
issues a series of requests to obtain the result one "chunk" at a time,
and concatenates those chunks internally. Each request contains offset
and length variables that specify which portion of the result shall be
retrieved.
Today, Winedbg handles this by generating the entire result data each
time a request is received and slicing out the requested range for the
response. This is not only inefficient due to repeated computation,
but also prone to race condition since the result may change between
successive chunk requests due to the dynamic nature of some commands
such as "libraries" and "threads."
Fix this by cacheing the result into a buffer at the first request, and
use the buffer to serve successive chunk requests. The cache is
invalidated when the remote requests a different object, or the debugger
reaches the end of the result cache buffer.
Signed-off-by: Jinoh Kang <jinoh.kang.kr@gmail.com>
Signed-off-by: Rémi Bernon <rbernon@codeweavers.com>
Signed-off-by: Alexandre Julliard <julliard@winehq.org>
Define a handler lookup table for qXfer commands and use it.
This facilitates implementing more qXfer commands and cacheing reply
data.
Signed-off-by: Jinoh Kang <jinoh.kang.kr@gmail.com>
Signed-off-by: Rémi Bernon <rbernon@codeweavers.com>
Signed-off-by: Alexandre Julliard <julliard@winehq.org>
Some dynamic strings (e.g. loaded image paths) may contain XML special
characters which breaks parsing.
Fix this by escaping all dynamic strings (i.e. character data and
attribute values) that go into the XML replies.
Signed-off-by: Jinoh Kang <jinoh.kang.kr@gmail.com>
Signed-off-by: Rémi Bernon <rbernon@codeweavers.com>
Signed-off-by: Alexandre Julliard <julliard@winehq.org>
Today, gdbproxy reuses the same buffer for both the qXfer reply and the
actual GDB packet reply. This worked well, since each byte in the qXfer
reply buffer matched 1:1 to each byte in the actual GDB reply packet.
Since we escape special characters now, this property no longer holds
and a single byte in qXfer reply will take up to two bytes in the GDB
reply packet. This causes offsets to shift, preventing the
offset/length response slicing (part of GDB protocol) from working
correctly.
Fix this by writing the qXfer reply data in a separate buffer, and
performing slicing out of it.
Signed-off-by: Jinoh Kang <jinoh.kang.kr@gmail.com>
Signed-off-by: Rémi Bernon <rbernon@codeweavers.com>
Signed-off-by: Alexandre Julliard <julliard@winehq.org>
This is required for a subsequent patch that adds buffering for
GDB qXfer reply data.
Signed-off-by: Jinoh Kang <jinoh.kang.kr@gmail.com>
Signed-off-by: Rémi Bernon <rbernon@codeweavers.com>
Signed-off-by: Alexandre Julliard <julliard@winehq.org>
There are four special characters in GDB's remote serial protocol:
- '$' (0x24): start of packet
- '}' (0x7D): escape
- '*' (0x2A): run-length encoding repeat count delimiter
- '#' (0x23): end of packet; start of checksum
In particular, the '#' and '}' characters are problematic since they
are often used in library filenames. A few examples:
- %SystemRoot%\assembly\NativeImages_v[.NET ver]\[module+hash]#\*\*.dll
- {CLSID or UUID}\*\.dll
To make GDB happy with those filenames, we scan for those characters and
escape them properly.
While we are at it, also remove the assert in the packet_reply function
that checks for '$' and '#' in the packet payload.
Signed-off-by: Jinoh Kang <jinoh.kang.kr@gmail.com>
Signed-off-by: Rémi Bernon <rbernon@codeweavers.com>
Signed-off-by: Alexandre Julliard <julliard@winehq.org>
packet_query uses sscanf format "%x" to parse out offset and length
values. Since %x corresponds to unsigned int in the C standard, adjust
the variable types appropriately.
Signed-off-by: Jinoh Kang <jinoh.kang.kr@gmail.com>
Signed-off-by: Rémi Bernon <rbernon@codeweavers.com>
Signed-off-by: Alexandre Julliard <julliard@winehq.org>
winedbg is now built with msvcrt, so just use realloc() directly
instead of Win32 heap functions.
Signed-off-by: Jinoh Kang <jinoh.kang.kr@gmail.com>
Signed-off-by: Rémi Bernon <rbernon@codeweavers.com>
Signed-off-by: Alexandre Julliard <julliard@winehq.org>
This allows to simplify a bit the frame internal storage
(no longer using IMAGEHLP_STACK_FRAME structure).
Signed-off-by: Eric Pouech <eric.pouech@gmail.com>
Signed-off-by: Alexandre Julliard <julliard@winehq.org>
Eric Pouech